| 耐酸耐火浇注料的性能 |
| 添加时间：2018/10/9 16:58:42 浏览次数： |
| 1、耐酸浇注料，厚度为10-20毫米，分格施工，分格缝间距2-3米，缝宽可谓15-20毫米，缝内用你教填满密实。 1. Acid-resistant castable, thickness of 10-20mm, parting construction, parting gap 2-3m, the width of the joint can be said to be 15-20mm, you use your teaching to fill the tight seam. 2、耐酸浇注料还可衬砌花岗岩块材，结合层和缝一般为10—15毫米。 2. Acid resistant castable can also be used for lining granite blocks. The bonding layer and seam are generally 10 to 15 mm. 3、耐酸浇注料施工要求和KPI胶泥施工相同。 3. The construction requirement of acid resistant castable is the same as that of KPI cement. 4、耐酸浇注料可用于化工、轻工、冶炼、酸洗、石油、农药、食品、电镀、点解等工业部门的反应釜、储罐、塔、电解槽、地沟、地坪、发酵池等整体，浇铸或内衬，加入钢筋后可做为结构防腐设备。 4. Acid-resistant castables can be used in the reactor, tank, tower, electrolytic tank, ditch, floor, fermentation tank of chemical, light industry, smelting, pickling, petroleum, pesticide, food, electroplating, point hydrolysis and other industrial departments. Casting or lining can be used as structural anticorrosion equipment. 5、在碳钢设备内部浇铸时碳钢设备的施工表明应喷砂除锈，在水泥混凝土设备内部浇铸时，应将设备表面的油迹、灰尘清理干净。 5. The construction of carbon steel equipment during the internal casting of carbon steel equipment indicates that sand blasting should be used to remove rust, and oil stains and dust on the surface of equipment should be cleaned up during the internal casting of cement concrete equipment. 6、浇铸用的模板结构必须严紧，尺寸准确，并具有足够的刚度、高度以50厘米为宜。 6. The formwork structure for casting must be rigid, accurate in size, with sufficient stiffness and suitable height of 50 cm. 7、施工前模板表面应涂油，然后将塑料膜衬于模板表面，接头部位延长5—10厘米。 7. Before construction, the surface of the formwork should be coated with oil, then the plastic film should be lined on the surface of the formwork, and the joint position should be extended by 5-10 cm. 8、搅拌的容器与工具必须清洁干燥。 8, stirring containers and tools must be clean and dry. 9、施工现场的温度须在15℃以上，雨季施工应搭建防雨棚。 9, the temperature of the construction site must be above 15 C, and rain shelter should be built in rainy season. 10、按KPI混凝土和硅酸钾的配合比进行充分搅拌均匀。 10. Mix well according to the mix ratio of KPI concrete and potassium silicate. 11、将搅拌好的物料注入模板内，并进行人工搅实或机械振动。 11. Mix the material into the template and artificially stir or mechanically vibrate. 12、每次装料深度以30厘米为宜。 12, each loading depth of 30 cm is appropriate. 找耐火材料网提醒，凡上述项目检查不合格时应处理合格后方可施工。过期失效的材料不得使用。 We should remind the refractory net to remind us that when the above items are not qualified, they should be treated before they can be constructed. Materials that fail to expire shall not be used. |
| 上一页 什么是树脂耐酸胶泥?其包括哪些材料? |
| 下一页 耐酸耐火浇注料的施工要求 |
Copyright © 技术支持：遨游网络